PA66 FRIANYL® C3 H V0 Celanese Corporation
So sánhBảng thông số kỹ thuật
| impact performance | Điều kiện kiểm tra | Phương pháp kiểm tra | Kết quả kiểm tra |
|---|---|---|---|
| Charpy Notched Impact Strength | Charpy Notched Impact Strength -30°C | ISO 179/1eA | 3.5 kJ/m² |
| Charpy Notched Impact Strength | Charpy Notched Impact Strength 23°C | ISO 179/1eA | 4.5 kJ/m² |
| Impact strength of simply supported beam without notch | Impact strength of simply supported beam without notch -30°C | ISO 179/1eU | 70 kJ/m² |
| Impact strength of simply supported beam without notch | Impact strength of simply supported beam without notch 23°C | ISO 179/1eU | 80 kJ/m² |
| Impact strength of cantilever beam gap | Impact strength of cantilever beam gap -30°C | ISO 180/A | 2.5 kJ/m² |
| Impact strength of cantilever beam gap | Impact strength of cantilever beam gap 23°C | ISO 180/A | 3.5 kJ/m² |
| flammability | Điều kiện kiểm tra | Phương pháp kiểm tra | Kết quả kiểm tra |
|---|---|---|---|
| UL flame retardant rating | UL flame retardant rating 0.40mm | UL 94 | V-0 |
| UL flame retardant rating | UL flame retardant rating 0.8mm | UL 94 | V-0 |
| UL flame retardant rating | UL flame retardant rating 1.6mm | UL 94 | V-0 |
| UL flame retardant rating | UL flame retardant rating 3.2mm | UL 94 | V-0 |
| Burning wire flammability index | Burning wire flammability index 0.8mm | IEC 60695-2-12 | 960 °C |
| Burning wire flammability index | Burning wire flammability index 3.2mm | IEC 60695-2-12 | 960 °C |
| Ignition temperature of heating wire | Ignition temperature of heating wire 3.2mm | IEC 60695-2-13 | 900 °C |
| Extreme Oxygen Index | Extreme Oxygen Index | ISO 4589-2 | 29 % |
| mechanical properties | Điều kiện kiểm tra | Phương pháp kiểm tra | Kết quả kiểm tra |
|---|---|---|---|
| Tensile modulus | Tensile modulus 23°C | ISO 527-2 | 3600 MPa |
| tensile strength | tensile strength Yield,23°C | ISO 527-2 | 80.0 MPa |
| Tensile strain | Tensile strain Yield,23°C | ISO 527-2 | 5.0 % |
| thermal performance | Điều kiện kiểm tra | Phương pháp kiểm tra | Kết quả kiểm tra |
|---|---|---|---|
| Hot deformation temperature | Hot deformation temperature 0.45MPa,Unannealed | ISO 75-2/B | 205 °C |
| Hot deformation temperature | Hot deformation temperature 1.8MPa,Unannealed | ISO 75-2/A | 80.0 °C |
| Continuous use temperature | Continuous use temperature | IEC 60216 | 110 °C |
| Ball Pressure Test | Ball Pressure Test 125°C | IEC 60695-10-2 | Pass |
| Ball Pressure Test | Ball Pressure Test 165°C | IEC 60695-10-2 | Pass |
| Physical properties | Điều kiện kiểm tra | Phương pháp kiểm tra | Kết quả kiểm tra |
|---|---|---|---|
| Water absorption rate | Water absorption rate Saturation,23°C | ISO 62 | 7.5 % |
| density | density 23°C | ISO 1183 | 1.17 g/cm³ |
| Shrinkage rate | Shrinkage rate TD:23°C | ISO 294-4 | 1.3 % |
| Shrinkage rate | Shrinkage rate MD:23°C | ISO 294-4 | 1.3 % |
| Water absorption rate | Water absorption rate 23°C,24hr | ISO 62 | 1.5 % |
| Electrical performance | Điều kiện kiểm tra | Phương pháp kiểm tra | Kết quả kiểm tra |
|---|---|---|---|
| Needle flame test | Needle flame test 1.00mm | IEC 60695-11-5 | Pass |
| Needle flame test | Needle flame test 2.00mm | IEC 60695-11-5 | Pass |
| Surface resistivity | Surface resistivity | IEC 60093 | 1E+13 ohms |
| Volume resistivity | Volume resistivity 23°C | IEC 60093 | 1E+15 ohms·cm |
| Dielectric strength | Dielectric strength 2.00mm | IEC 60243-1 | 18 kV/mm |
| Compared to the anti leakage trace index | Compared to the anti leakage trace index 3.20mm,SolutionA | IEC 60112 | PLC 0 |