Polyester, TS MPV 7270 RASCHIG GmbH
So sánhBảng thông số kỹ thuật
| impact performance | Điều kiện kiểm tra | Phương pháp kiểm tra | Kết quả kiểm tra |
|---|---|---|---|
| Impact strength of simply supported beam without notch | Impact strength of simply supported beam without notch Injection | ISO 179/1eU | 10to12 kJ/m² |
| Impact strength of simply supported beam without notch | Impact strength of simply supported beam without notch Compression Molded | ISO 179/1eU | 8.0to10 kJ/m² |
| Charpy Notched Impact Strength | Charpy Notched Impact Strength Injection | ISO 179/1eA | 1.5to2.5 kJ/m² |
| Charpy Notched Impact Strength | Charpy Notched Impact Strength Compression Molded | ISO 179/1eA | 1.5to2.5 kJ/m² |
| flammability | Điều kiện kiểm tra | Phương pháp kiểm tra | Kết quả kiểm tra |
|---|---|---|---|
| UL flame retardant rating | UL flame retardant rating 1.5mm | UL 94 | HB |
| mechanical properties | Điều kiện kiểm tra | Phương pháp kiểm tra | Kết quả kiểm tra |
|---|---|---|---|
| tensile strength | tensile strength Injection | ISO 527-2 | 50.0to60.0 MPa |
| tensile strength | tensile strength CompressionMolded | ISO 527-2 | 30.0to50.0 MPa |
| Tensile modulus | Tensile modulus Injection | ISO 527-2 | 5000to7000 MPa |
| Tensile modulus | Tensile modulus Compression Molded | ISO 527-2 | 4000to6000 MPa |
| bending strength | bending strength Compression Molded | ISO 178 | 70.0to90.0 MPa |
| Bending modulus | Bending modulus Injection | ISO 178 | 8000to9000 MPa |
| Bending modulus | Bending modulus Compression Molded | ISO 178 | 8000to9000 MPa |
| Compressive stress | Compressive stress | ISO 604 | 150to200 MPa |
| bending strength | bending strength Injection | ISO 178 | 90.0to110 MPa |
| thermal performance | Điều kiện kiểm tra | Phương pháp kiểm tra | Kết quả kiểm tra |
|---|---|---|---|
| Maximum operating temperature | Maximum operating temperature 20,000h | IEC 60216 | 150 °C |
| Maximum operating temperature | Maximum operating temperature <50h | IEC 60216 | 190 °C |
| thermal conductivity | thermal conductivity | ASTME1461 | 0.50to0.60 W/m/K |
| Linear coefficient of thermal expansion | Linear coefficient of thermal expansion MD：50to100°C | ISO 11359-2 | 2.0E-5到3.0E-5 cm/cm/°C |
| Hot deformation temperature | Hot deformation temperature 8.0MPa,Unannealed | ISO 75-2/C | 80.0to110 °C |
| Hot deformation temperature | Hot deformation temperature 1.8MPa,Unannealed | ISO 75-2/A | 180to200 °C |
| Physical properties | Điều kiện kiểm tra | Phương pháp kiểm tra | Kết quả kiểm tra |
|---|---|---|---|
| Shrinkage rate | Shrinkage rate | ISO 2577 | 0.20to0.40 % |
| Apparent density | Apparent density | ISO 60 | 0.80to1.00 g/cm³ |
| density | density | ISO 1183 | 1.70to1.80 g/cm³ |
| Shrinkage rate | Shrinkage rate MD：--2 | ISO 2577 | 0.70to1.0 % |
| Shrinkage rate | Shrinkage rate MD：--3 | ISO 2577 | 0.50to0.80 % |
| Water absorption rate | Water absorption rate 23°C,24hr | ISO 62 | <1.0 % |
| Electrical performance | Điều kiện kiểm tra | Phương pháp kiểm tra | Kết quả kiểm tra |
|---|---|---|---|
| Surface resistivity | Surface resistivity | IEC 60093 | 1.0E+11到1.0E+12 ohms |
| Volume resistivity | Volume resistivity | IEC 60093 | 1.0E+12到1.0E+13 ohms·cm |
| Dielectric strength | Dielectric strength | IEC 60243-1 | 30to40 kV/mm |
| Relative permittivity | Relative permittivity 100Hz | IEC 60250 | 5.007.00 |
| Relative permittivity | Relative permittivity 1MHz | IEC 60250 | 4.005.00 |
| Dissipation factor | Dissipation factor 100Hz | IEC 60250 | 0.10to0.20 |
| Dissipation factor | Dissipation factor 1MHz | IEC 60250 | 0.030to0.050 |
| Arc resistance | Arc resistance | ASTM D495 | PLC 4 |
| Compared to the anti leakage trace index | Compared to the anti leakage trace index | IEC 60112 | PLC 0 |
| Supplementary Information | Điều kiện kiểm tra | Phương pháp kiểm tra | Kết quả kiểm tra |
|---|---|---|---|
| Compression molding temperature | Compression molding temperature | 160to180 °C | |
| Compression molding pressure | Compression molding pressure | >10.0 MPa |