PC LEXAN™ 121R-21051 SABIC INNOVATIVE SINGAPHORE
- Đặc tính:Độ nhớt thấpChống cháyTrong suốt
- Lĩnh vực ứng dụng:Hồ sơVật liệu xây dựng
So sánh
Xem giáBảng thông số kỹ thuật
| optical performance | Điều kiện kiểm tra | Phương pháp kiểm tra | Kết quả kiểm tra |
|---|---|---|---|
| turbidity | turbidity 2540μm | ASTM D1003 | 1.0 % |
| transmissivity | transmissivity 2540μm | ASTM D1003 | 88.0 % |
| Refractive index | Refractive index | ASTM D542 | 1.586 |
| impact performance | Điều kiện kiểm tra | Phương pháp kiểm tra | Kết quả kiểm tra |
|---|---|---|---|
| Impact strength of cantilever beam gap | Impact strength of cantilever beam gap | ASTM D1822 | 546 kJ/m² |
| Dart impact | Dart impact 23°C | ASTM D3029 | 169 J |
| Dart impact | Dart impact 23°C,EnergyatPeakLoad | ASTM D3763 | 62.1 J |
| Suspended wall beam without notch impact strength | Suspended wall beam without notch impact strength 23°C | ISO 180/1U | NoBreak |
| Suspended wall beam without notch impact strength | Suspended wall beam without notch impact strength -30°C | ISO 180/1U | NoBreak |
| Impact strength of cantilever beam gap | Impact strength of cantilever beam gap 23°C | ASTM D4812 | 3200 J/m |
| Impact strength of cantilever beam gap | Impact strength of cantilever beam gap 23°C | ISO 180/1A | 65 kJ/m² |
| Impact strength of cantilever beam gap | Impact strength of cantilever beam gap -30°C | ISO 180/1A | 11 kJ/m² |
| Impact strength of cantilever beam gap | Impact strength of cantilever beam gap 23°C | ASTM D256 | 690 J/m |
| Impact strength of simply supported beam without notch | Impact strength of simply supported beam without notch 23°C | ISO 179/1eU | NoBreak |
| Impact strength of simply supported beam without notch | Impact strength of simply supported beam without notch -30°C | ISO 179/1eU | NoBreak |
| Charpy Notched Impact Strength | Charpy Notched Impact Strength 23°C | ISO 179/1eA | 65 kJ/m² |
| Charpy Notched Impact Strength | Charpy Notched Impact Strength -30°C | ISO 179/1eA | 12 kJ/m² |
| flammability | Điều kiện kiểm tra | Phương pháp kiểm tra | Kết quả kiểm tra |
|---|---|---|---|
| Radiation board grade | Radiation board grade UL | YES | |
| UL flame retardant rating | UL flame retardant rating 0.70mm | UL 94 | HB |
| mechanical properties | Điều kiện kiểm tra | Phương pháp kiểm tra | Kết quả kiểm tra |
|---|---|---|---|
| elongation | elongation Break | ASTM D638 | 130 % |
| Bending modulus | Bending modulus 50.0mmSpan | ASTM D790 | 2340 Mpa |
| bending strength | bending strength Yield,50.0mmSpan | ASTM D790 | 96.5 Mpa |
| Taber abraser | Taber abraser 1000Cycles,1000g,CS-17Wheel | ASTM D1044 | 10.0 mg |
| elongation | elongation Yield | ASTM D638 | 7.0 % |
| tensile strength | tensile strength Break | ASTM D638 | 68.9 Mpa |
| tensile strength | tensile strength Yield | ASTM D638 | 62.1 Mpa |
| thermal performance | Điều kiện kiểm tra | Phương pháp kiểm tra | Kết quả kiểm tra |
|---|---|---|---|
| RTI Str | RTI Str | UL 746 | 130 °C |
| RTI Elec | RTI Elec | UL 746 | 130 °C |
| RTI Imp | RTI Imp | UL 746 | 130 °C |
| thermal conductivity | thermal conductivity | ASTMC177 | 0.25 W/m/K |
| specific heat | specific heat | ASTMC351 | 1260 J/kg/°C |
| Linear coefficient of thermal expansion | Linear coefficient of thermal expansion MD：-40to95°C | ASTME831 | 6.8E-05 cm/cm/°C |
| Vicat softening temperature | Vicat softening temperature | ASTM D15257 | 154 °C |
| Hot deformation temperature | Hot deformation temperature 0.45MPa,Unannealed,6.40mm | ASTM D648 | 138 °C |
| Hot deformation temperature | Hot deformation temperature 1.8MPa,Unannealed,6.40mm | ASTM D648 | 129 °C |
| Physical properties | Điều kiện kiểm tra | Phương pháp kiểm tra | Kết quả kiểm tra |
|---|---|---|---|
| Outdoor applicability | Outdoor applicability | UL 746C | f2 |
| Water absorption rate | Water absorption rate Equilibrium,100°C | ASTM D570 | 0.58 % |
| Water absorption rate | Water absorption rate Equilibrium,23°C | ASTM D570 | 0.35 % |
| Water absorption rate | Water absorption rate 24hr | ASTM D570 | 0.15 % |
| Shrinkage rate | Shrinkage rate MD：3.20mm | Internal Method | 0.50-0.70 % |
| melt mass-flow rate | melt mass-flow rate 300°C/1.2kg | ASTM D1238 | 18 g/10min |
| density | density | ASTM D792 | 1.19 g/cm³ |
| Specific volume | Specific volume | ASTM D792 | 0.835 cm³/g |
| density | density | ASTM D792 | 1.20 g/cm³ |
| Electrical performance | Điều kiện kiểm tra | Phương pháp kiểm tra | Kết quả kiểm tra |
|---|---|---|---|
| High voltage arc tracing rate | High voltage arc tracing rate HVTR | UL 746 | PLC 2 |
| Compared to the anti leakage trace index | Compared to the anti leakage trace index CTI | UL 746 | PLC 2 |
| High arc combustion index | High arc combustion index HAI | UL 746 | PLC 1 |
| Dissipation factor | Dissipation factor 1MHz | ASTM D150 | 0.010 |
| Dissipation factor | Dissipation factor 60Hz | ASTM D150 | 9E-04 |
| Dielectric constant | Dielectric constant 50Hz | ASTM D150 | 3.17 |
| Dielectric constant | Dielectric constant 60Hz | ASTM D150 | 3.17 |
| Dielectric constant | Dielectric constant 1MHz | ASTM D150 | 2.96 |
| Dissipation factor | Dissipation factor 50Hz | ASTM D150 | 9E-04 |
| Dielectric strength | Dielectric strength 3.20mm,inAir | ASTM D149 | 15 KV/mm |
| Hot wire ignition | Hot wire ignition HWI | UL 746 | PLC 2 |
| Volume resistivity | Volume resistivity | ASTM D257 | >1.0E+17 ohms·cm |
| hardness | Điều kiện kiểm tra | Phương pháp kiểm tra | Kết quả kiểm tra |
|---|---|---|---|
| Rockwell hardness | Rockwell hardness M-Sale | ASTM D785 | 70 |
| Rockwell hardness | Rockwell hardness R-Sale | ASTM D785 | 118 |
