So sánh vật liệu

Thông tin sản phẩm
Tên sản phẩm
Tên thương hiệu
Lĩnh vực ứng dụng
Đặc tính
Giấy chứng nhận
Đơn giá
PA6/6T TKR4355G10 BK23215 BASF GERMANY
Ultramid® 
Ứng dụng điện tử,Phụ tùng ô tô
Hấp thụ nước thấp,Độ cứng
- -
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--

Thông số kỹ thuật

impact performanceĐiều kiện kiểm traPhương pháp kiểm traBASF GERMANY/TKR4355G10 BK23215
Impact strength of simply supported beam without notch-30°CISO 179/1eU85 kJ/m²
23°CISO 179/1eU90 kJ/m²
flammabilityĐiều kiện kiểm traPhương pháp kiểm traBASF GERMANY/TKR4355G10 BK23215
Flammability levelUL 94HB
Polymer AbbreviationPA6T/6-GF50
mechanical propertiesĐiều kiện kiểm traPhương pháp kiểm traBASF GERMANY/TKR4355G10 BK23215
Tensile modulusISO 527-217000 Mpa
Tensile strainBreakISO 527-22.4 %
Tensile creep modulus1000 hrISO 899-1-- Mpa
tensile strengthBreakISO 527-2240 Mpa
injectionĐiều kiện kiểm traPhương pháp kiểm traBASF GERMANY/TKR4355G10 BK23215
drying time8.0 hr
Screw speed< 18 m/min
Suggested maximum moisture content0.15 %
Temperature in the middle of the barrel310 °C
Mold temperature80 to 120 °C
Temperature at the rear of the barrel300 °C
Processing (melt) temperature310 to 330 °C
Hopper temperature80 °C
drying temperature110 °C
Temperature at the front of the material cylinder320 °C
Spray nozzle temperature320 °C
Residence Time< 5.0 min
thermal performanceĐiều kiện kiểm traPhương pháp kiểm traBASF GERMANY/TKR4355G10 BK23215
thermal conductivityDIN 526120.32 W/m/K
Linear coefficient of thermal expansionFlow : 23 to 55°CISO 11359-21.8E-5 cm/cm/°C
Across Flow : 23 to 55°CISO 11359-25.0E-5 到 6.0E-5 cm/cm/°C
Melting temperatureISO 11357-3285 °C
Temperature index - at 50% loss of tensile strength--5IEC 60216170 °C
--6IEC 60216145 °C
Maximum operating temperature短周期操作260 °C
specific heat1000 J/kg/°C
Hot deformation temperature1.8 MPa, UnannealedISO 75-2/A245 °C
Physical propertiesĐiều kiện kiểm traPhương pháp kiểm traBASF GERMANY/TKR4355G10 BK23215
Shrinkage rate横向FlowISO 294-40.66 %
Stickiness96% H2SO4ISO 307135 cm³/g
Shrinkage rateFlowISO 294-40.20 %
Mold Shrinkage - Constrained0.29 %
Water absorption rateSaturation, 23°CISO 623.5 to 4.5 %
Apparent density0.70 g/cm³
Water absorption rateEquilibrium, 23°C, 50% RHISO 620.40 to 0.80 %
Electrical performanceĐiều kiện kiểm traPhương pháp kiểm traBASF GERMANY/TKR4355G10 BK23215
Compared to the anti leakage trace indexSolution AIEC 60112PLC 0
Dielectric strengthIEC 60243-133 KV/mm
Volume resistivityIEC 600931.0E+17 ohms·cm
Relative permittivity1 MHzIEC 602504.70
Surface resistivityIEC 60093-- ohms
Dissipation factor1 MHzIEC 602500.020