So sánh vật liệu

Thông tin sản phẩm
Tên sản phẩm
Tên thương hiệu
Lĩnh vực ứng dụng
Đặc tính
Giấy chứng nhận
Đơn giá
PC EXL9330 GY4D167 SABIC INNOVATIVE THAILAND
LEXAN™ 
Trang chủ,Sản phẩm tường mỏng,Thực phẩm
Chống cháy,Tăng cường,Chống tia cực tím
- -
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--

Thông số kỹ thuật

impact performanceĐiều kiện kiểm traPhương pháp kiểm traSABIC INNOVATIVE THAILAND/EXL9330 GY4D167
Suspended wall beam without notch impact strength-30°CISO 180/1U无断裂
Impact strength of simply supported beam without notch-30°CISO 179/1eU无断裂
Suspended wall beam without notch impact strength23°CISO 180/1U无断裂
Impact strength of simply supported beam without notch23°CISO 179/1eU无断裂
Charpy Notched Impact Strength23°CISO 179/1eA75 kJ/m²
Dart impact23°C, Total EnergyASTM D376352.0 J
Charpy Notched Impact Strength-30°CISO 179/1eA60 kJ/m²
flammabilityĐiều kiện kiểm traPhương pháp kiểm traSABIC INNOVATIVE THAILAND/EXL9330 GY4D167
UL flame retardant rating3.0 mmUL 945VA
Extreme Oxygen IndexISO 4589-235 %
Hot filament ignition temperature1.0 mmIEC 60695-2-13825 °C
UL flame retardant rating1.5 mmUL 94V-0
Burning wire flammability index1.0 mmIEC 60695-2-12960 °C
mechanical propertiesĐiều kiện kiểm traPhương pháp kiểm traSABIC INNOVATIVE THAILAND/EXL9330 GY4D167
elongationYieldISO 527-2/506.0 %
Yield3ASTM D6386.0 %
Tensile modulus--2ASTM D6382100 Mpa
Bending modulus--5ISO 1782200 Mpa
tensile strengthYieldISO 527-2/5055.0 Mpa
BreakISO 527-2/5060.0 Mpa
Tensile modulus--ISO 527-2/12100 Mpa
bending strengthYield, 50.0 mm Span4ASTM D79088.0 Mpa
tensile strengthBreak3ASTM D63861.0 Mpa
Bending modulus50.0 mm Span4ASTM D7902060 Mpa
bending strength--5,6ISO 17885.0 Mpa
elongationBreak3ASTM D638130 %
tensile strengthYield3ASTM D63858.0 Mpa
elongationBreakISO 527-2/50130 %
injectionĐiều kiện kiểm traPhương pháp kiểm traSABIC INNOVATIVE THAILAND/EXL9330 GY4D167
Suggested maximum moisture content0.020 %
Mold temperature70 to 95 °C
Processing (melt) temperature295 to 315 °C
drying temperature120 °C
Suggested injection volume40 to 60 %
drying time3.0 to 4.0 hr
Screw speed40 to 70 rpm
Temperature in the middle of the barrel280 to 305 °C
Temperature at the rear of the barrel215 to 295 °C
Exhaust hole depth0.025 to 0.076 mm
Back pressure0.300 to 0.700 Mpa
Temperature at the front of the material cylinder295 to 315 °C
Spray nozzle temperature290 to 310 °C
thermal performanceĐiều kiện kiểm traPhương pháp kiểm traSABIC INNOVATIVE THAILAND/EXL9330 GY4D167
RTI ElecUL 746125 °C
Hot deformation temperature0.45 MPa, Unannealed, 3.20 mmASTM D648134 °C
Vicat softening temperature--ASTM D152512142 °C
Hot deformation temperature1.8 MPa, Unannealed, 3.20 mmASTM D648120 °C
Vicat softening temperature--ISO 306/B50140 °C
RTIUL 746125 °C
Linear coefficient of thermal expansionAcross Flow : 23 to 80°CISO 11359-27.7E-5 cm/cm/°C
Flow : -40 to 40°CASTM E8316.7E-5 cm/cm/°C
Hot deformation temperature0.45 MPa, Unannealed, 4.00 mm, 100 mm Span11ISO 75-2/Be135 °C
1.8 MPa, Unannealed, 4.00 mm, 100 mm Span11ISO 75-2/Ae124 °C
RTI ImpUL 746115 °C
Ball Pressure Test123 to 127°CIEC 60695-10-2通过
Linear coefficient of thermal expansionAcross Flow : -40 to 40°CASTM E8316.7E-5 cm/cm/°C
Flow : 23 to 80°CISO 11359-27.2E-5 cm/cm/°C
Hot deformation temperature1.8 MPa, Unannealed, 6.40 mmASTM D648124 °C
Physical propertiesĐiều kiện kiểm traPhương pháp kiểm traSABIC INNOVATIVE THAILAND/EXL9330 GY4D167
Outdoor applicabilityUL 746Cf1
melt mass-flow rate300°C/1.2 kgASTM D123810 g/10 min
Shrinkage rateAcross FlowFlow : 3.20 mmInternal Method0.40 - 0.80 %
density--ISO 11831.19 g/cm³
Shrinkage rateFlow : 3.20 mmInternal Method0.40 - 0.80 %
Water absorption rateSaturation, 23°CISO 620.35 %
Melt Volume Flow Rate (MVR)300°C/1.2 kgISO 11339.00 cm3/10min
Water absorption rateEquilibrium, 23°C, 50% RHISO 620.15 %
density--ASTM D7921.18 g/cm³
Electrical performanceĐiều kiện kiểm traPhương pháp kiểm traSABIC INNOVATIVE THAILAND/EXL9330 GY4D167
Dissipation factor1 MHzASTM D1508.5E-3
60 HzASTM D1502.4E-3
50 HzIEC 602501.0E-3
Dielectric strength3.20 mm, in OilASTM D14917 KV/mm
Compared to the anti leakage trace indexUL 746PLC 3
High arc combustion indexUL 746PLC 0
Dielectric constant50 HzIEC 602502.60
50 kHzASTM D1502.95
Dissipation factor60 HzIEC 602501.0E-3
Dielectric strength3.20 mm, in OilIEC 60243-116 KV/mm
Dielectric constant60 HzASTM D1502.95
Hot wire ignitionUL 746PLC 1
Dielectric constant1 MHzIEC 602502.70
Volume resistivityIEC 60093> 1.0E+15 ohms·cm
Dielectric constant1 MHzASTM D1502.90
Compared to the anti leakage trace indexIEC 60112PLC 3
Dielectric constant60 HzIEC 602502.60
Dissipation factor50 HzASTM D1502.4E-3
Surface resistivityIEC 60093> 1.0E+15 ohms
hardnessĐiều kiện kiểm traPhương pháp kiểm traSABIC INNOVATIVE THAILAND/EXL9330 GY4D167
Ball Pressure TestH 358/30ISO 2039-190.0 Mpa