Thiết bị cỏ,Thiết bị sân vườn,Ứng dụng công nghiệp,Phụ tùng ô tô bên ngoài,Lĩnh vực điện,Lĩnh vực điện tử,Lĩnh vực ứng dụng xây dựn,Ứng dụng ngoài trời,Thiết bị điện,Phụ tùng mui xe,Sản phẩm y tế,Sản phẩm chăm sóc,Túi nhựa,Phụ tùng nội thất ô tô,Trang chủ,Hàng gia dụng,Ứng dụng dầu,Sản phẩm gas,Hàng thể thao,Ứng dụng dệt,Ứng dụng chiếu sáng

Gia cố sợi thủy tinh,Kích thước ổn định,Độ cứng cao,Sức mạnh cao,Chịu nhiệt

Giá nội địa

Miền Nam Việt Nam (xung quanh Hồ Chí Minh)

₫ 85.330/KG

Thông số kỹ thuật

impact performance	Điều kiện kiểm tra	Phương pháp kiểm tra	SABIC INNOVATIVE KOREA/420SEO-701
Suspended wall beam without notch impact strength	-30°C8	ISO 180/1U	45 kJ/m²
Impact strength of simply supported beam without notch	-30°C	ISO 179/1eU	50 kJ/m²
Suspended wall beam without notch impact strength	23°C	ASTM D4812	620 J/m
Charpy Notched Impact Strength	23°C	ISO 179/1eA	7.0 kJ/m²
Impact strength of simply supported beam without notch	23°C	ISO 179/1eU	50 kJ/m²
Dart impact	23°C, Total Energy	ASTM D3763	5.00 J
Charpy Notched Impact Strength	-30°C	ISO 179/1eA	6.0 kJ/m²
Suspended wall beam without notch impact strength	23°C8	ISO 180/1U	45 kJ/m²

flammability	Điều kiện kiểm tra	Phương pháp kiểm tra	SABIC INNOVATIVE KOREA/420SEO-701
UL flame retardant rating	0.71 mm	UL 94	V-0
Extreme Oxygen Index		ISO 4589-2	32 %
UL flame retardant rating	0.40 mm	UL 94	V-2
UL flame retardant rating		2.0 mm	UL 94	5VA
Burning wire flammability index	1.0 mm	IEC 60695-2-12	960 °C

mechanical properties	Điều kiện kiểm tra	Phương pháp kiểm tra	SABIC INNOVATIVE KOREA/420SEO-701
elongation	Break	ISO 527-2/5	1.9 %
tensile strength	Break	ISO 527-2/5	120 Mpa
Bending modulus	--6	ISO 178	9500 Mpa
Tensile modulus	--3	ASTM D638	12000 Mpa
Tensile modulus		--	ISO 527-2/1	10000 Mpa
elongation	Yield4	ASTM D638	2.0 %
tensile strength	Break4	ASTM D638	120 Mpa
bending strength	Break, 50.0 mm Span5	ASTM D790	186 Mpa
Taber abraser	1000 Cycles, 1000 g, CS-17 Wheel	Internal Method	22.0 mg
Bending modulus	50.0 mm Span5	ASTM D790	9800 Mpa
tensile strength	Yield	ISO 527-2/5	120 Mpa
elongation	Break4	ASTM D638	2.0 %
elongation		Yield	ISO 527-2/5	1.9 %
bending strength	--	ISO 178	180 Mpa
tensile strength	Yield4	ASTM D638	120 Mpa

injection	Điều kiện kiểm tra	Phương pháp kiểm tra	SABIC INNOVATIVE KOREA/420SEO-701
Suggested maximum moisture content			0.020 %
Mold temperature			65 to 90 °C
Processing (melt) temperature			255 to 275 °C
drying temperature			120 °C
Suggested injection volume			40 to 80 %
drying time			3.0 to 4.0 hr
Screw speed			50 to 80 rpm
Temperature in the middle of the barrel			250 to 270 °C
Temperature at the rear of the barrel			245 to 265 °C
Exhaust hole depth			0.025 to 0.038 mm
Temperature at the front of the material cylinder			255 to 275 °C
Back pressure			0.300 to 0.700 Mpa
Spray nozzle temperature			250 to 270 °C

thermal performance	Điều kiện kiểm tra	Phương pháp kiểm tra	SABIC INNOVATIVE KOREA/420SEO-701
RTI Elec		UL 746	130 °C
Hot deformation temperature	0.45 MPa, Unannealed, 3.20 mm	ASTM D648	212 °C
		1.8 MPa, Unannealed, 3.20 mm	ASTM D648	200 °C
		0.45 MPa, Unannealed, 4.00 mm, 100 mm Span9	ISO 75-2/Be	220 °C
Vicat softening temperature	--	ASTM D152510	200 °C
RTI		UL 746	140 °C
Linear coefficient of thermal expansion	Across Flow : -40°C	ISO 11359-2	8.9E-5 cm/cm/°C
		Across Flow : 23 to 80°C	ISO 11359-2	1.2E-4 cm/cm/°C
		Flow : -40 to 40°C	ASTM E831	2.5E-5 cm/cm/°C
Hot deformation temperature	1.8 MPa, Unannealed, 4.00 mm, 64.0 mm Span8	ISO 75-2/Af	200 °C
Hot deformation temperature		1.8 MPa, Unannealed, 4.00 mm, 100 mm Span9	ISO 75-2/Ae	195 °C
RTI Imp		UL 746	130 °C
Ball Pressure Test	123 to 127°C	IEC 60695-10-2	通过
Linear coefficient of thermal expansion	Across Flow : -40 to 40°C	ASTM E831	8.9E-5 cm/cm/°C
Linear coefficient of thermal expansion		Flow : 23 to 80°C	ISO 11359-2	2.5E-5 cm/cm/°C
Vicat softening temperature	--	ISO 306/A50	220 °C
thermal conductivity		ISO 8302	0.25 W/m/K

Physical properties	Điều kiện kiểm tra	Phương pháp kiểm tra	SABIC INNOVATIVE KOREA/420SEO-701
Specific volume		ASTM D792	0.610 cm³/g
Melt Volume Flow Rate (MVR)	250°C/5.0 kg	ISO 1133	29.0 cm3/10min
melt mass-flow rate	250°C/5.0 kg	ASTM D1238	42 g/10 min
Outdoor applicability		UL 746C	f2
Shrinkage rate	Across FlowFlow : 3.20 mm	Internal Method	0.50 - 1.0 %
		Flow : 3.20 mm	Internal Method	0.50 - 0.70 %
		Flow 2	Internal Method	0.10 - 0.50 %
Water absorption rate	Saturation, 23°C	ISO 62	0.090 %
Shrinkage rate	Across FlowFlow 2	Internal Method	0.40 - 0.80 %
Water absorption rate	Equilibrium, 23°C, 50% RH	ISO 62	0.070 %

Electrical performance	Điều kiện kiểm tra	Phương pháp kiểm tra	SABIC INNOVATIVE KOREA/420SEO-701
Arc resistance		ASTM D495	PLC 6
Compared to the anti leakage trace index	Solution B	IEC 60112	PLC 4
Volume resistivity		ASTM D257	> 1.0E+15 ohms·cm
Dissipation factor	1 MHz	ASTM D150	0.020
High voltage arc tracing rate		UL 746	PLC 4
Dissipation factor	50 Hz	IEC 60250	1.0E-3
Compared to the anti leakage trace index		UL 746	PLC 3
High arc combustion index		UL 746	PLC 0
Dielectric constant	50 Hz	IEC 60250	3.30
Compared to the anti leakage trace index	--	IEC 60112	PLC 3
Dissipation factor	60 Hz	IEC 60250	1.0E-3
Dielectric strength	3.20 mm, in Oil	IEC 60243-1	16 KV/mm
		1.60 mm, in Oil	ASTM D149	24 KV/mm
		3.20 mm, in Air	ASTM D149	19 KV/mm
Hot wire ignition		UL 746	PLC 2
Dielectric strength	0.800 mm, in Oil	IEC 60243-1	23 KV/mm
Dielectric strength		1.60 mm, in Oil	IEC 60243-1	22 KV/mm
Dielectric constant	1 MHz	IEC 60250	3.30
		1 MHz	ASTM D150	3.70
		100 Hz	ASTM D150	3.80
Dissipation factor	100 Hz	ASTM D150	2.0E-3
Dielectric constant	60 Hz	IEC 60250	3.30
Surface resistivity		IEC 60093	> 1.0E+15 ohms
Dissipation factor	1 MHz	IEC 60250	0.010

hardness	Điều kiện kiểm tra	Phương pháp kiểm tra	SABIC INNOVATIVE KOREA/420SEO-701
Rockwell hardness	R -Sale	ISO 2039-2	119
Ball Pressure Test	H 358/30	ISO 2039-1	118 Mpa
Rockwell hardness	R-Scale	ASTM D785	119